This documentation is for version 2.3.0. Other versions.

Table of Contents

Flash layout

Even though file system is stored on the same flash chip as the program, programming new sketch will not modify file system contents. This allows to use file system to store sketch data, configuration files, or content for Web server.

The following diagram illustrates flash layout used in Arduino environment:

|--------------|-------|---------------|--|--|--|--|--|
^              ^       ^               ^     ^
Sketch    OTA update   File system   EEPROM  WiFi config (SDK)

File system size depends on the flash chip size. Depending on the board which is selected in IDE, you have the following options for flash size:

Board Flash chip size, bytes File system size, bytes
Generic module 512k 64k, 128k
Generic module 1M 64k, 128k, 256k, 512k
Generic module 2M 1M
Generic module 4M 3M
Adafruit HUZZAH 4M 1M, 3M
ESPresso Lite 1.0 4M 1M, 3M
ESPresso Lite 2.0 4M 1M, 3M
NodeMCU 0.9 4M 1M, 3M
NodeMCU 1.0 4M 1M, 3M
Olimex MOD-WIFI-ESP8266(-DEV) 2M 1M
SparkFun Thing 512k 64k
SweetPea ESP-210 4M 1M, 3M
WeMos D1 & D1 mini 4M 1M, 3M
ESPDuino 4M 1M, 3M

Note: to use any of file system functions in the sketch, add the following include to the sketch:

#include "FS.h"

Uploading files to file system

ESP8266FS is a tool which integrates into the Arduino IDE. It adds a menu item to Tools menu for uploading the contents of sketch data directory into ESP8266 flash file system.

File system object (SPIFFS)

begin

SPIFFS.begin()

This method mounts SPIFFS file system. It must be called before any other FS APIs are used. Returns true if file system was mounted successfully, false otherwise.

end

SPIFFS.end()

This method unmounts SPIFFS file system. Use this method before updating SPIFFS using OTA.

format

SPIFFS.format()

Formats the file system. May be called either before or after calling begin. Returns true if formatting was successful.

open

SPIFFS.open(path, mode)

Opens a file. path should be an absolute path starting with a slash (e.g. /dir/filename.txt). mode is a string specifying access mode. It can be one of "r", "w", "a", "r+", "w+", "a+". Meaning of these modes is the same as for fopen C function.

   r      Open text file for reading.  The stream is positioned at the
          beginning of the file.

   r+     Open for reading and writing.  The stream is positioned at the
          beginning of the file.

   w      Truncate file to zero length or create text file for writing.
          The stream is positioned at the beginning of the file.

   w+     Open for reading and writing.  The file is created if it does
          not exist, otherwise it is truncated.  The stream is
          positioned at the beginning of the file.

   a      Open for appending (writing at end of file).  The file is
          created if it does not exist.  The stream is positioned at the
          end of the file.

   a+     Open for reading and appending (writing at end of file).  The
          file is created if it does not exist.  The initial file
          position for reading is at the beginning of the file, but
          output is always appended to the end of the file.

Returns File object. To check whether the file was opened successfully, use the boolean operator.

File f = SPIFFS.open("/f.txt", "w");
if (!f) {
    Serial.println("file open failed");
}

exists

SPIFFS.exists(path)

Returns true if a file with given path exists, false otherwise.

openDir

SPIFFS.openDir(path)

Opens a directory given its absolute path. Returns a Dir object.

remove

SPIFFS.remove(path)

Deletes the file given its absolute path. Returns true if file was deleted successfully.

rename

SPIFFS.rename(pathFrom, pathTo)

Renames file from pathFrom to pathTo. Paths must be absolute. Returns true if file was renamed successfully.

info

FSInfo fs_info;
SPIFFS.info(fs_info);

Fills FSInfo structure with information about the file system. Returns true is successful, false otherwise.

Filesystem information structure

struct FSInfo {
    size_t totalBytes;
    size_t usedBytes;
    size_t blockSize;
    size_t pageSize;
    size_t maxOpenFiles;
    size_t maxPathLength;
};

This is the structure which may be filled using FS::info method. - totalBytes — total size of useful data on the file system - usedBytes — number of bytes used by files - blockSize — SPIFFS block size - pageSize — SPIFFS logical page size - maxOpenFiles — max number of files which may be open simultaneously - maxPathLength — max file name length (including one byte for zero termination)

Directory object (Dir)

The purpose of Dir object is to iterate over files inside a directory. It provides three methods: next(), fileName(), and openFile(mode).

The following example shows how it should be used:

Dir dir = SPIFFS.openDir("/data");
while (dir.next()) {
    Serial.print(dir.fileName());
    File f = dir.openFile("r");
    Serial.println(f.size());
}

dir.next() returns true while there are files in the directory to iterate over. It must be called before calling fileName and openFile functions.

openFile method takes mode argument which has the same meaning as for SPIFFS.open function.

File object

SPIFFS.open and dir.openFile functions return a File object. This object supports all the functions of Stream, so you can use readBytes, findUntil, parseInt, println, and all other Stream methods.

There are also some functions which are specific to File object.

seek

file.seek(offset, mode)

This function behaves like fseek C function. Depending on the value of mode, it moves current position in a file as follows:

Returns true if position was set successfully.

position

file.position()

Returns the current position inside the file, in bytes.

size

file.size()

Returns file size, in bytes.

name

String name = file.name();

Returns file name, as const char*. Convert it to String for storage.

close

file.close()

Close the file. No other operations should be performed on File object after close function was called.